Routerstation - 3 LAN, 3 MiniPCI, USB2, 680MHZ 64MB 16MB

    Routerstation - 3 LAN, 3 MiniPCI, USB2, 680MHZ 64MB 16MB

    UBNT-RS
    Available
    A$145.00
    Tax included

    Routerstation - 3 LAN, 3 MiniPCI, USB2, 680MHZ 64MB 16MB

     

    Routerstation - 3 LAN, 3 MiniPCI, USB2, 680MHZ 64MB 16MB


    Performance:

    • Featuring a fast 680MHz MIPS 24K CPU, 64MB RAM, and 16MB Flash; RouterStation provides a excellent horsepower for a variety of processor intensive multi-radio system applications.

    Additional Features:

    • Up to 3 mini-PCI radios, 3 10/100 ethernet interfaces, a 5A power supply for multiple hi-power card support, USB 2.0, and enhanced temperature operating performance and ethernet ESD protection for carrier applications.

    Over all system configuration:

    • CPU Atheros AR7161 MIPS 24K running @ 680MHz
    • MEMORY DDR 64MB
    • FLASH SPI 16MB
    • Three MINI-PCI Slots supports Type IIIA
    • One USB 2.0 Host
    • One UART


    Power Supply Range 12VDC to 24VDC

    • Using Higher voltage is recommended since it will use lower current
    • Typical Power Consumption is 3W idle no radios present
    • 5W idle One Radio present
    • 7W while passing 100Mbps traffic
    • Single RJ45 "J1" Is for WAN and Passive Power Over Ethernet


    Ethernet Interface

    • J1 Single WAN port 10/100
    • J2 Dual Lan Port 10/100
    • Ethernet Phy switch, ADMTEK "Infineon" ADM6996FC

    Supported IO

    UART J3 6 pin Header
    Terminal Settings 115200 baud, 8 bits, nor parity, 1 stop bit.

    Pin Out 
    Pin13.3VDC
    Pin2S_in
    Pin3NC
    Pin4NC
    Pin5S_out
    Pin6GND

     

    USB 2.0 Host J7
    5 Pin Header typical PC USB header

    Pin Out 
    Pin15VDC
    Pin2D-
    Pin3D+
    Pin4GND
    Pin5GND

     

    JTAG Port "J4"
    14 Pin header

    Pin Out   
    Pin1TRSTPin2GND
    Pin3TDIPin4GND
    Pin5TDOPin6GND
    Pin7TMSPin8GND
    Pin9TCKPin10GND
    Pin11RSTPin12NC
    Pin13NCPin143.3VDC

     

    USER GPIO Header "J33"
    Single Row 7 Pin Header Also next to it J5 dual row header to enable pull-up or pull-down for each GPIO user selectable in case User needs 1 Low or 1 High GPIO

    J33 Pin out and Strapping option "place shunt to enable strapping option"

    Pin OutNAMEJ5 STRAPPING
    Pin1GPIO_0PULL LOW
    Pin2GPIO_1PULL LOW
    Pin3GPIO_3PULL LOW
    Pin4GPIO_4PULL LOW
    Pin5GPIO_5PULL HIGH
    Pin6GPIO_6PULL HIGH
    Pin7GPIO_7PULL HIGH

     


    RESET BUTTON "SW4"

    Uses GPIO_8 with weak pull-up, 1 Low, for Resting back to factory defaults or multiple functions software dependent.


    LED INDICATORS

    LEDNAMEFUNCTION
    D29POWER3.3VDC
    D24RFRADIO ActGPIO_2
    DS4WANLink/Act
    DS13LAN1Link/Act
    DS12LAN2Link/Act

     

     

    No reviews
    Product added to wishlist
    Product added to compare.

    We use cookies to ensure that we give you the best experience on our website,

    if you continue to use this site we will assume that you are happy with it.